2017年1月13日星期五
What are the types of vertical pipeline centrifugal pump
Vertical pipeline centrifugal pump repair :
Mainly to clean, replace and repair the wear and corrosion of parts, and adjust the body, to ensure that the equipment can be used to the next planned overhaul. General repairs (dimensions) by the inspection personnel responsible for repair workers, post operation coordination. The main contents are as follows.
1.Check the cleaning filter.
2.Check and adjust the coupling of the coaxial degree and the axial gap, the replacement of the vulnerable parts of the coupling.
3.Check bearing and oil path, replace oil (grease).
4.Check the cooling or heating system and remove scale.
5.Eliminate defects and leakage found in operation. Check and tighten all bolts.
6.Inspection, cleaning pump population, export valve, replace the gasket.
Repair of vertical pipeline centrifugal pump:
Besides minor projects, but also the main components of the equipment for local repair and replace those identified by not continue to use until the next repair time is the main parts.
1.Including minor content.
2.Disassembly, inspection and repair of magnetic couplings in the inner and outer magnetic rotor and isolation kits and replacement parts.
3.Inspection of all parts of the wear, corrosion and erosion degree, to be repaired or replaced.
4.Inspection shaft wear, corrosion and straightness, to repair.
5.Determination of the impeller static balance and check the amount of shaking the rotor.
6.Check the bearing sleeve wear, adjusting clearance, and replacement of bearings.
7.Check and adjust the impeller seal ring, the balance plate and other parts of the gap.
8.Check or check pressure gauge.
9.Inspection, cleaning and motor repair.
Vertical pipeline centrifugal pump overhaul :
All or part of the demolition of equipment, replacement and repair has abrasion and corrosion of parts, in order to restore the original performance of the equipment (including re installation, calibration, paint and re pouring equipment etc.). In order to improve the technical level and the comprehensive function of the device, the equipment can also be used to carry out technological transformation.
1.Including the contents of the repair.
2.Replacement of the impeller.
3.Replace the pump shaft.
4.Pump test thickness, identification, necessary repairs.
5.Measure and adjust the level of pump body.
6.Corrosion.
Equipment maintenance must be carried out after the test run.
Method for regulating the flow of pipeline centrifugal pump
The working point of the pipeline centrifugal pump is determined by the characteristic curve of the pump and the characteristic curve of the pipeline system. So, the change of the characteristic curve of any one can achieve the purpose of flow regulation.
At present, the flow regulation of the centrifugal pump is mainly controlled by the regulating valve, the variable speed control of the pump, and the pump and series regulation. Because of the principle of regulation in different ways, the resulting energy loss is not the same, in order to find the minimum energy consumption, energy saving, the highest effect is the best way of flow control, must fully understand the relationship between the flow adjustment of centrifugal pump and energy consumption.
Several main methods of regulating the flow rate of the centrifugal pump are analyzed by the characteristic curve of the centrifugal pump and the pipeline system: the adjustment of the outlet valve, the variable speed regulation of the pump and the series and parallel regulation of the pump. With the characteristic curves of the energy loss of pump outlet valve adjustment and speed adjustment in two ways, and compared it with the speed regulation, outlet valve regulating flow of traffic than you can better save energy, with centrifugal pump outlet valve: small, directly blocked the flow of liquid, but the work of the centrifugal pump energy did not decrease; if adopt variable speed control, reduce the speed of centrifugal pump, the corresponding reduction in the flow, so as to reduce the flow and energy saving.
2016年12月20日星期二
How to solve the problem of horizontal multi-stage pump
1.Horizontal multistage pump does not absorb water or water. The cause of this failure is mostly due to the end of valve stuck, part of the blockage of water, high water or water pipe leakage is too high. Should be checked one by one, taken at the end of valve repair, clear the blockage and correct the steering and other processing.
2.Pipeline leakage or leakage. No more than nuts tightened due. If the leakage is not serious, can be applied to cement slurry, mud or soft soap in the leakage; if the joints Water Leakage, tighten the nut wrench can be used. Serious leakage, leakage, must be re assembled.
3.Multi-stage centrifugal pump severe vibration. May be the motor rotor is not balanced or shaft coupling. Sometimes bearing wear, bending, rotating parts of the relaxation, rupture, pipeline stent is not strong also cause vibration. Should be adjusted, reinforcement, inspection or replacement.
4.The impeller is bad. When the damage is not large, can be repaired. Hard alloy should be replaced or plated when the damage is serious. Completely damaged, the impeller should be removed, the repair shop to repair.
5.Horizontal multi-stage pump shaft bending. Is due to the impact load, belt pulled too tight, causing incorrect installation. If the bend is not serious, can be used manually screw to correct, but not too hard, in case of a complete break.
订阅:
博文 (Atom)