2016年10月30日星期日

Adjustment methods of centrifugal pump and the energy consumption analysis

Through the analysis of the characteristic curves of centrifugal pump and pipeline system of centrifugal pump flow control main ways: export valve adjustment, pump variable speed adjustment and pump series, in parallel to adjust. Export was analyzed by using the characteristic curves of regulating valve and pump speed regulating energy loss in two ways, and has carried on the contrast, points out that the centrifugal pump with variable speed regulating flow than with export flow adjusting valve can better save energy consumption, and energy saving efficiency and the size of the flow changes. In practical application, you should pay attention to the range of speed regulation, can better use centrifugal pump variable speed control.
Centrifugal pump is widely used in chemical industry system of a kind of fluid machinery. It has to adapt to the wide scope of performance (including flow, pressure head and adapted to the nature of the medium), small volume, simple structure, easy operation, low operation cost, a lot of advantage. Usually, the selected centrifugal pump flow rate and pressure head may and asked for in line, or change due to the production task, technological requirements, at this time are required to adjust the discharge pump, essence is to change the working point of centrifugal pump. Centrifugal pump working point is by the characteristic curve of pump and piping system joint decision characteristic curve, therefore, any change of characteristic curve can achieve the purpose of flow control. At present, the centrifugal pump flow control ways are regulating valve, variable speed control and pump control and, series adjustment, etc. Due to all sorts of the principle of adjustment for different, in addition to have their own advantages and disadvantages, the energy loss is different also, in order to seek the best, the minimum energy consumption, the most energy-efficient way of flow control, must fully understand the flow of a centrifugal pump adjustment methods and the relationship between the energy consumption.
1 the main pump flow control
1.1 change the pipeline characteristic curve
Change the simplest method is to use centrifugal pump pump discharge valve to control the opening, the essence of which is the location of the change of pipeline characteristic curve to change the working point of the pump.
1.2 change the centrifugal pump characteristic curve
According to the proportion law and the law of cutting, change the pump rotation speed, the pump structure (such as the method of cutting impeller diameter, etc.) both methods could change characteristic curve of centrifugal pump, so as to achieve the purpose of flow adjustment, change the pressure head at the same time). But for the pump work, has changed the pump structure method is not very convenient, and because change the structure of the pump, reduces the versatility of the pump, even though it at some point adjustment convenient traffic economy [1], and rarely used in production. Just how changes in centrifugal pump flow of speed adjusting method. From figure 1, when change the pump speed adjusting flow rate decreased from Q1 to Q2, the pump speed (or motor speed) decreased from n1 to n2, speed under n2 pump characteristic curve of Q - H and the pipeline characteristic curve He = H0 + G1Qe2 (line curve does not change) to point A3 (Q2, H3), point A3 for the new speed adjusting flow after working point. The adjustment method of adjustment effect, quick, safe and reliable, can prolong the service life of the pump, save electricity, reduce speed running also can effectively reduce the NPSH of centrifugal pump NPSHr, away from the pump cavitation area, reduce the possibility of centrifugal pump cavitation occurred [2]. The disadvantage is that change the pump speed by variable frequency technology are needed to change the prime mover (usually) of the motor speed, principle of complex, investment is bigger, and the flow adjustment range is small.
1.3 pump series, and even the adjustment way
When a single centrifugal pump can't meet the delivery task, can use of centrifugal pump in parallel or in series operation. With two sets of the same type of centrifugal pump in parallel, although the head changed little, but increased the total transportation flow, the total efficiency of the pump in parallel with a single pump efficiency is the same; Centrifugal pump series when the total pressure head, flow rate change is not big, the total efficiency of the pump with single pump efficiency is the same.
Energy consumption analysis of two pumps under different adjustment modes
Analysis of energy consumption under different adjustment modes, the article in view of the present regulating valve and pump variable speed regulation is widely adopted by two types of regulation. Due to centrifugal pump and, series aims to improve the pressure head or flow, in the field of chemical industry use is not much, analyze its energy consumption can be combined with figure 2, the method is basically the same.

Pump selection principles and steps

Pump is a kind of a lot of wide range of general-purpose machinery and equipment, it is widely used in petroleum, chemical, electric power, metallurgy, mining, choose ship, light industry, agriculture, civil and defense departments, occupies an important position in national economy. According to 79 statistics, pump output reached 1.256 million units in China. Pump power consumption accounted for more than 21% of the national power consumption. So vigorously reduce pump energy consumption, to save energy use is of great significance.
Designed and developed in recent years, we have pump industry a lot of high efficiency and energy saving products, such as IHF, CQB, such as the FSB, UHB models of pump products, to reduce the energy consumption of the pump plays a positive role. But now in various fields of national economy, due to the unreasonable type selection, many of the running status of pump in the unreasonable operation efficiency is low, waste a lot of energy. And due to the unreasonable selection of pump, it was impossible to use, or use the maintenance cost increases, the economic benefit is low. Therefore, reasonable choose pump is of great significance to save energy.
So-called reasonable selected pump, is to consider investment and operation cost of pump unit and pumping stations comprehensive technical and economic indexes, such as make it conform to the principle of economy, safety and applicable. In particular, has the following several aspects:
Must meet the requirements of the use of flow and head, requiring the pump running work time points (device characteristic curves with the pump performance curve intersection) often remain within the range of efficient operation, save power and not easy attaint parts.
The choice of the pump should not only small volume, light weight, cheap, and has good characteristics and higher efficiency.
Has good resistance to cavitation performance, this can not only reduce the pump room of the excavation depth, and the water pump cavitation occurs, smooth operation, long service life.
Built according to the selected pump pumping station, the project less investment, low operating cost.
The second section selection steps
A basic data, list:
1, the characteristics of the medium: the name of the medium, specific gravity, viscosity, corrosive, toxic, etc.
In 2, medium contained in the body of particle diameter, how much content.
3, medium temperature (℃)
4, need traffic
General industrial pump can be ignored in the process of pipeline system leakage, but affected by the change of flow must be considered. Agricultural use, if is adopted, open channel water pump must also consider leakage and evaporation.
5, pressure: suction tank pressure, water pressure, the pressure drop of pipeline system (head losses).
6, pipeline system data (diameter, length, kinds and number of pipeline accessories, vacuum pressure to the pool geometry level, etc.).
Should also make the device characteristic curve, if necessary.
Decorate in the design line, should pay attention to the following items:
A, reasonable choose pipe diameter, pipe diameter is big, under the same flow rate, liquid flow velocity is small, small resistance loss, but the price is high, the pipe diameter is small, can lead to resistance losses increase sharply, increase the selected pump lift, installed with power increasing, the cost and operation cost are increased. So from the perspective of technical and economic comprehensive consideration.
B, discharge pipe and pipe joints should be considered are the biggest pressure.
C, pipeline layout should decorate straight pipe as far as possible, try to reduce the attachment and try to narrow the pipe length, pipe must turn, elbow bend radius should be 3 ~ 5 times the diameter of the pipe, as much as possible Angle is greater than 90 ℃.
D, the discharge side of the pump must be installed with the valve (ball valve or valve, etc.) and check valve. Used to adjust the point of pump, valve check valve when the fluid flow reversal can prevent the pump inversion, and makes the pump to avoid water hammer blow. (when the liquid flow back, will produce a great reverse pressure, make the pump damage)

2016年10月28日星期五

Ten reasons and solutions of Pump lift not enough

Weihu pump industry in the past for the user maintenance encountered problem in the process of water pump is not enough, one of them is water pump lift weihu pump industry pump maintenance technicians here today to simple about the cause and the solution, the pump head is not a lack of enough pump head might mechanical electrical system may also have reasons.
Pump lift is not the cause and the solution
One of the reasons for pump head is not enough, liquid contains excessive amounts of air or gas. Solution: reduce the liquid temperature out of gas.
Pump head is not enough for another, the speed is too low. weihu pump industry solution: check whether the voltage is in the range of rated voltage, check whether the motor running normally.
The cause of the pump head is not enough 3, motor turn to right. weihu pump industry solution: because the power of fire against money and zero line, changing a line, the problem is human reason, is generally not easy to appear.
Four of the cause of the pump head is not enough, the total head above water pump design head. Solution: replace the head higher levels of the water pump.
Five of the cause of the pump head is not enough, the concentration of the liquid and the design value. Solution: replace conform to the requirements of the pump.
Six of the cause of the pump head is not enough, the operation flow rate is far lower than the minimum flow. weihu pump industry solution: replace conform to the requirements of the pump.
Seven of the cause of the pump head is not enough, abrasion and ring. Solution: replace the qualified new wear ring.
Eight of the cause of the pump head is not enough, the damage of impeller. Solution: replace the qualified new impeller.
Nine of the cause of the pump head is not enough, resulting in pump head gasket damage caused by internal leak is not enough. Solution: replace the qualified new gasket.
Ten of the cause of the pump head is not enough, sundries mixed in the pump, the impeller and port blocked. Solution: remove the pump clear clutter.

What are the cause of the pump not flow water?

 Shanghai weihu pump industry to provide users with the pump maintenance encountered in the process of various types of failures, specifically today there is not the cause of the water pump? In the past we also encountered many pump without water, so we have what are not the cause of the water pump as a summary, said below mentioned possible reasons one by one.
A, suction side issues
1, and there is no water injection pump
2, water pump or suction tube is not completely filled with liquid
3, suction head is too high, more than the pump capacity
4, suction pressure is too close to the liquid pressure gasification
5, air pockets in the suction side
6, suction side not fully immersed in a liquid
Second, the system reason
1, the speed is too low
2, motor turning right
3, total head above water pump design head
4, improper operation
Second, the mechanical reason
The impeller is influenced by external factors.
Above is a summary of what are not the cause of the water pump, of course, there could be other reasons, so much the cause of water pump water not may appear a few projects at the same time coexist,  weihu special remind what kind of reason is specific to on site need to be given, to ensure accurate quickly remove the water pump is not a failure.

Submersible pump failure phenomenon and elimination method

1, check the motor. To see if the motor has to check motor starting not starting to eliminate circuit fault can be  whether motor wiring connection correct check whether electric pump reverse electric pump reversal switch power supply cord.
2, check the line. Look after the road if there is a wall, rupture, filter water blockage. If the pipeline rupture should be repair welding or in tube unclog fault can be ruled out.
3, check the pump casing seal check whether the impeller is damaged. Elimination method  change the new seal, impeller.
Second, the motor can't start with hum
1, check whether a motor circuit breakers check whether the voltage is the voltage is too low. After repair, adjust voltage normal fault can be ruled out.
2, check whether there is foreign body inside the impeller, the bearing damage to remove foreign bodies or replace the bearing.
Three, current is too large, ammeter pointer swing
1, when buying a new pump for shaft bending, bearing different heart immediately get back the sales department or factory.
2, check whether the thrust bearing is badly worn impeller with ring friction marks. Elimination method replace the thrust bearing and thrust plate of the impeller rotates with sealing ring friction can no longer.
3, check the shaft and the shaft when relative rotation is flexible rotation is not flexible, should replace or repair the bearings.
4, dynamic water level dropped to below inlet. Traffic shall be reduced or in the well.
Four, severe vibration unit operation
1, check whether the connecting bolt is loose bolts should be tightened.
2, a motor rotor imbalance, imbalance of water pump impeller, motor or the pump shaft bending failure should be sent after the factory for processing.

Water pump overhaul time, pump overhaul period

Water pump overhaul time, pump overhaul period
Water pump overhaul period according to the operation and technical conditions to determine of the unit. SL255-2000 "pumping technology management discipline" regulation for pump overhaul cycle: the main pump for 3 to 5 years or run a 2500-15000 hours, the main motor 3 to 8 years or run a 3000-20000 hours. And according to the situation in advance or delay the overhaul.
When determining pump overhaul cycle and workload, attention should be paid to the following aspects:
(1) if there are no special requirements, avoid removing technology can good parts and institutions.
(2) should try to extend the repair cycle. According to the wear and tear of spare parts, the operation test of similar equipment, equipment runtime performance indicators to determine the pump overhaul period, regardless of the wear of some parts. Therefore, should have a plan to overhaul, in order to ensure the normal operation of the unit.
(3) avoid remove all parts of the body, especially the precision and smoothness, cooperate with the parts, which need high institutions.

The advantage of the sewage plant using sewage pump parsing

Sewage plant for processing production using sewage submersible pump, can will get the robustness of the play, the effect of water treatment is mainly manifested in the following two benefits:
First, strong corrosion resistance
This kind of wastewater treatment will inevitably encounter strong acidic or alkaline substances exist, when the use of this kind of submersible pump will change in the resistance to corrosive effect, because of that it is making more friends to realize its special performance.
Sewage submersible pump in pollution resistance on the performance of the obtained the effective processing and change, have the opportunity to know and see, bring more friends very good effect.
Second, prevent plugging ability
Because the sewage submersible pump itself requires water processing and processing, so also increased on the ability of anti clogging. Use of such materials for promotion and application, let more people to realize the existence of its dominant role. Because there will be a lot of garbage composition of sewage, will inevitably affect the normal water effect to prevent clogging submersible pump at this point if you can choose to come to production and processing, believe that will reach the ideal mode in effect.